Here’s How to Tune Skis for a Smooth Ride Every Time

If you’ve been skiing for a while, it’s time to learn how to tune skis yourself. Getting them tuned at a shop gets expensive in the long run.

How important is tuning? Well, it’s crucial if you want to pour the speed on or make sharp turns without snags. So, you’ll get a lot of use out of knowing how to tune skis at home. And get this! It’s easy.



​image by pixabay

A basic ski tune-up consists of a few simple steps. Tuning the edges is the main event. However, touching up the base and applying new wax are also important steps.

Learning how to tune skis is simple. And if you use a complete ski tuning kit, the whole process will be smooth.

Demon Complete Ski Tune Kit with Wax and Brush Kit-…

  • Comes with a Flat file, Edge…
  • Bonus**Includes 133 grams of…
  • Everything you need for a…
  • The Iron is High quality and…
  • The Iron has an easy turn dial…




Base damage is pretty much inevitable when you ski. When rocks and other hard things in the snow leave scratches and dents, it affects the way your skis glide. Thankfully, it’s easy to fix.

What you need

  • Base cleaner

  • Rubbing alcohol

  • Scrubber or wire brush

  • Metal scraper

  • P-tex stick

  • Lighter

  • Clean towels

A base repair kit gives you most of these things. The rest is easy to supplement.

Tools4Boards PTEX Ski & Snowboard Base Repair Kit

  • Fix gouges and scrapes with…
  • Maroon – medium, Grey – fine…
  • 5 pcs structure sand paper,…
  • 3 Black and 3 Clear Ptex…
  • Stainless steel scraper, use…


Keeping things clean is essential when learning how to tune skis.

First, scrape the base to remove any excess base material. If there’s a stubborn piece, use a knife. Then, brush the base to remove any dust and debris. Go over the whole ski.

Next, we need to remove some wax around the damaged area. So, put some base cleaner on it and let it sit for a few minutes. Lastly, put some rubbing alcohol on a towel and use it to remove the base cleaner residue.


image by pixabay​​​


Once the base is clean, we can start the repairs. Light one end of your P-tex stick with a lighter or a match. It starts dripping quickly, so make sure to hold it over something you don’t mind dripping on. The metal scraper is a good idea.

Since you’re dealing with molten plastic, you must be careful not to burn yourself. This is the only hazardous step of how to tune skis.

Next, drip your P-tex into the gouges and scratches of the base. Keep the dripping tip close to the surface to prevent splashing. Also, don’t hold the P-tex stick directly against the base, or it may burn it.


First, let the repaired base cool a bit. Then, scrape off the excess P-tex with your metal scraper.

That’s it for base repairs. Now for the main part of how to tune skis.


Burrs and rust along the edges make your skis slower and may worsen handling. Cleaning and sharpening these edges is the main element of how to tune skis.

What you’ll need

  • Diamond stone

  • Gummi stone

  • Edge tool

  • Clean towels

  • Rubbing alcohol

There aren’t many tools you need for this. An edge tuning kit covers everything you don’t already have at home.

Complete Edge Care Kit Base-Side Ski Edge Tool +3 Diamonds…

  • Complete Edge Care Kit -…
  • This one tool is all you need…
  • One Gumi or Gummi Stone for…
  • Three diamond stones included!…
  • Don’t know your angles? Before…


The easiest way to find the spots that cause drag is to run a towel along the edge from tip to tail. You’ll feel the towel catch on burrs, and you may even see some fibers left behind.


Tuning the base edge is the main part of how to tune skis.

So, wet your coarser diamond stone and use it to file down the burs with slow, gentle motions. Remember only to go from front to back and stay clear of the base material.

Then, use a finer diamond stone and make a few passes along the whole edge from tip to tail. Finish up by polishing the edges with your gummi stone to polish off any rust.


Tuning the sidewalls is an essential part of how to tune skis. Also, it’s very simple.

First, wet your diamond stone and make a few passes from tip to tail. Keep it flat against the sidewall and use long, smooth motions.

Next, repeat the same process with your gummi stone. Now, all that’s left to do on the edges is to clean up. However, you may want to detune the contact points first.


Detuning your contact points can make it easier to pop out of turns and avoid accidents if you’re a beginner or intermediate skier. The contact points are the spots where the ski edge rounds out on the thicker parts near the tip and tail.

You can detune a contact point by running a wet file or coarse diamond stone over it and dulling the edge. Start around two inches in front of it, and finish around two inches behind it.

Detune the base edge first, and then the sidewall. Lastly, smooth things out with a fine wet diamond stone and a gummi stone.

Before you move on with how to tune skis, it’s time to clean up. Using rubbing alcohol and a towel, remove any metal shavings along the edges.


Even with perfectly smooth bases and tuned edges, there will still be friction if the wax isn’t good. Therefore, this is an important step in how to tune skis. Regularly waxing your skis is essential to optimal performance.

What you’ll need

  • Wax

  • Brushes

  • Plastic scraper

  • Iron

  • Rubbing alcohol

  • Clean towels

It’s best to use a waxing iron. While a regular iron can work, it’s not ideal, and it could burn your skis. The easiest solution is to get a complete tuning kit with a waxing iron.

Swix North Kit – Mass Transit

  • Our best selling North MASS…
  • Pocket EDGER and DIAMOND DISC…
  • Dual use BRUSH is perfect to…
  • All comes in a great sized BAG…


Is there any visible dirt on the base? Then use a wire brush to clean it.

When there’s no visible dirt, run your plastic scraper from tip to tail twice to scrape off any grime or excess wax. Then, wipe the whole base down with rubbing alcohol and a towel.


First, heat up your iron. Touch the wax against it from time to time to see if it’s hot enough. Once it’s able to melt the wax, it’s ready. If there’s any smoke, your iron is too hot.

Next, hold your wax and iron over the tip of the ski. Then, bring them together to start dripping wax onto the base. Continue down the ski in a zig-zag pattern.

Now, bring your iron to the tip and start ironing the wax. You don’t need to press it hard. Keep moving down the length of the ski at an even pace.

If you move it too slowly, you may damage the base material. However, moving too fast won’t let the wax penetrate the ski properly.

At the ideal pace, the trail of molten wax behind the iron should be a few inches long, but no more than five. Also, make sure that the ironed wax covers the whole width of the ski. If not, you’ll have to add more wax and start over.


Before you continue, the ski must cool for about an hour after waxing.

First, use your plastic scraper. Hold it at a 45-degree angle and scrape in long strokes with firm pressure. Start from the tip and use overlapping strokes until there are no more wax shavings.

Next, it’s time to clean the sides. For this, use the short ends of your scraper to avoid damaging the main scraping edges.

Then, use your nylon brush to clean out the tiny ridges in the base. Keep brushing until there are no wax flakes. Polish off the result with the horsehair brush. Take your time, because it gets better the more you brush.


Now you know how to tune skis like a pro. It’s easy if you get a proper ski tuning kit.

Demon Mechanic Elite X Ski Tuning Kit & Snowboard Tuning Kit…

  • Demon Mechanic Elite X Ski…
  • IRON SPEC* This Demon Wax Iron…
  • TOOLS INCLUDED* Elite X Edge…
  • WAX INCLUDED* 133gm High…
  • BAG SPEC* 1 internal…

Are your skis really worn out no matter how much tuning and TLC you’ve given them? Don’t feel bad! It happens to every set of skis eventually. But you’re in luck; when you’re ready to pick a new set, we can help you find the best skis for you.

Featured image by: Pixabay

Superfeet Green Review: An Insole With Your Comfort in Mind

We start our Superfeet Green review with a bold assertion: Your feet are the hardest working part of your body. They take you where you want to go. And whether you’re walking or running, hiking, biking, golfing, or just plain working, insoles such as Superfeet Green can give your tootsies a break.

Insoles are designed to slide into your shoes to deliver support and comfort to every part of your foot. They can also play a role in heading off or easing aches and pains that can come from overwork.

Superfeet Green insoles target individuals with high arches. They are just one part of a broad line of inserts made by Superfeet to address different sizes, shapes, and situations with your feet.

Have you come here wondering if these are right for you? Our Superfeet Green review will help you decide.


blue shoes

image by pixabay

To begin our Superfeet Green review, let’s first look at the broader category of insoles and what they do for our feet.

Insoles are thin pieces of material to provide support for your arches and other parts of your feet. They can be used both as a preventative measure, to lessen the chance of planter fasciitis or other conditions. They also can help ease existing pain, whether chronic or otherwise.

The primary function of insoles is to provide support for the foot and help keep your gait in proper alignment, so the muscles, tendons, and ligaments work in harmony.

As you consider our Superfeet Green review and read more about insoles, you might also come across the term “orthotics.” As a general matter, the two terms are interchangeable. Orthotics are more often used to refer to inserts that are professionally customized to your particular situation based on a prescription from your doctor.

Customers purchase insoles such as Superfeet on an over-the-counter basis. But the two categories have the same purpose, which is to deliver support and comfort throughout the day.

Inserts are a standard accessory for runners. But they’re also handy in hiking and many other activities on your feet.


For now, we don’t have to concern ourselves with the custom orthotic category. We’re talking about Superfeet, an employee-owned company based in Ferndale, Washington.

Superfeet makes a broad line of professional-grade over-the-counter insoles as well as footwear.

Superfeet GREEN Insoles, Professional-Grade High Arch…

  • FIT PROFILE: High volume /…
  • STABILIZER CAP: acts as the…
  • DEEP HEEL CUP: features the…
  • SUPERFEET SHAPE: a high…

The Superfeet Green line targets individuals with high arches. The inserts use a very dense foam that’s rigid when you need it but also provides flexibility. The idea isn’t to lock your foot into one place but to guide it to the most natural position for your body.

One area of your feet that takes a beating is the heel. The Superfeet Green insoles include a deep heel cup to take away the impact of connecting with the ground.

Superfeet insoles will retain their effectiveness for about a year — or, if you’re more active on your feet, for 500 miles. After that point, the support layers will start to break down.

Keep in mind that Superfeet Green inserts come with a break-in period. If you’ve never worn insoles before, they will take some time to feel comfortable on your feet. Don’t start with a lengthy run or walk with the insoles, as it denies your feet and the insole itself a chance to adjust.

A typical Superfeet review written by a happy customer will mention the fine line between softness and support.

Where to buy


comfortable shoes

gif by giphy

We consulted several sources to build our Superfeet Green review. Our initial focus was on understanding what the medical profession had to say about the effectiveness of insoles. So we consulted opinions from institutions such as Harvard Health Publishing and individual provider blogs such as Pain Science and Spectrum Foot Clinics.

To round out our Superfeet Green review, we also paid close attention to customer reviews on sites such as And, of course, we studied the information on the Superfeet site.

Our goal was to create a straightforward look at the Superfeet Green and what it can do for your feet.


Superfeet is a name you can’t escape when shopping for insoles. But it’s not the only name. The market offers excellent choices. And as part of our Superfeet Green review, we wanted to introduce you to some options.

One note: We stayed away from the Dr. Scholl’s brand. Consider those to be more “entry-level” inserts for more mild conditions. Our focus was on brands that provided insole technology comparable to Superfeet.


Spenco Total Support Max Shoe Insoles, Women’s 11-12/Men’s…

  • Rigid arch support for maximum…
  • For athletes looking for rigid…
  • Improves motion control to…
  • Advanced support for the arch…
  • Unconditionally guaranteed for…

Wherever you find Superfeet, the chances are good you will also find selections from Spenco, a North Carolina company. Like Superfeet, Spenco provides a full line of foot care products that include insoles and orthotics.

Spenco insoles aim to provide support across several on-your-feet activities — walking, running, cross-training, hiking, other sports, and even just for prolonged standing.

The Spenco Total Support Max brand is similar to Superfeet Green in that both address people with higher arches. Spenco takes a different approach, however. Spenco inserts include “pods” of varying degrees of hardness. These are placed at crucial areas of the foot to ease the amount of force on your feet.

Both Spenco and Superfeet seek to steer the foot in a way that reduces or eliminates “over-pronation,” which most foot experts believe can causes foot or leg problems.

The Max line is by design stiffer than other insoles made by Spenco. It targets the more serious athlete who is putting numerous miles on their legs during the week.

Customers indicate in their reviews that the Spenco inserts have successfully helped curb foot pain and correct over-pronation and even provide a solution to flat feet.

Where to buy


Powerstep Original Orthotics Insole, Blue/Black, Men’s…

  • Full length total support:…
  • Moderate cushioning: original…
  • Designed for comfort: The…
  • For every shoe: maintain…
  • Podiatrist designed: Powerstep…

We should point out in our Superfeet Green review that insoles are not just for men. Power Step, an Ohio-based company that is also employee-owned, offers insoles geared toward the specific needs of women.

PowerStep’s Original Insoles deliver moderate cushioning while at the same time building in the right amount of support for every part of your gait.

The original insoles are multi-purpose. You can use them in your athletic shoes, but also more casual or even dressier shoes. Sometimes the most significant impact on our feet happens during the day at work.

You might find these insoles to be thinner than the Superfeet Green. But keep focused on feel. As long as they provide the support you need, don’t let the width, or relative lack of it, impact your viewpoint.

Customers from a variety of professions leave enthusiastic reviews. They are loved by Army soldiers and nurses — people who are on their feet all the time. As with Superfeet, customers advise that the PowerStep line needs a breaking-in period.

Where to buy


Plantar Fasciitis Feet Insoles Arch Supports Orthotics…

  • LASTING COMFORT – arch support…
  • DEEP HEEL CUP- to maintain…

Our final insert alternative is the best-seller in its category on Amazon. You might find them to be a little more affordable than either the Superfeet or Spenco brands.

Walk-Hero inserts are similar to Superfeet Green in that they also come with a deep heel cup to assist with foot positioning on every step. The more in-line you are, the less chance you have for conditions such as plantar fasciitis or tendonitis.

Walk-Hero inserts also are useful in multiple applications — walking, running, hiking, working, even biking, and beyond. You can use them in both casual, work, and athletic footwear.

Customers note that these inserts may look and feel more substantial than either the Spenco or Superfeet, but that’s part of the attraction. With thickness comes reinforced support that you’ll appreciate on your feet.

Where to buy


As with any technology, you might wonder, “do I need these?” As runners ourselves, we don’t go a single mile without the right kind of insert. So, we’re definitely biased.

But everyone’s situation is a little different. There is no single right customer. Our advice is that if you are suffering from pain or discomfort, give a pair of inserts a whirl. You might be surprised just how good your feet start to feel.

Now we’d love to hear from you! Let us know in the comments section below what you think about our Superfeet Green review.

Featured image by: Amazon


How to Use a Bike Pump in 5 Simple Steps to Get You Rolling Again

A flat bike tire can ruin your mood if you don’t know how to use a bike pump. Instead of letting that happen, you can get back on the trail in a few easy steps. But, there are a few things you need to know first.

What kind of bike pump is the best to use? Do the types of tires matter? The truth is, you’ll need to make sure you have the right bike pump for your tires before getting started.



image by pixabay

The best bike pump for you will depend on the valve on your tires. Two kinds are easily distinguishable.

The first is a Schrader valve, also known as an American valve. It consists of a threaded metal piece with a thin metal stem inside it. If you press on the stem, you can hear air escape the tire. These are common on car tires, mountain bikes, and some road bikes.

The other valve is a Presta valve. It’s skinnier and longer than a Schrader, and it doesn’t have an internal valve stem. Instead, it has a valve cap that you unscrew to expose the stem.

Presta valves are common on more sophisticated road bikes.

Different bike pumps accommodate various valves, so it’s essential to choose a pump that’s compatible with your bike tires. You can also purchase an adapter.

Diamondback Bicycle Presta Valve Adaptors

  • Adapts presto valves for us…
  • Full low-lead brass…
  • Rubber O-rings keep air…


bike wheels

image by unsplash

Once you have the right pump, you can learn how to use a bike pump.

Whether you have a floor or a hand pump, the process is the same. You’ll need to prepare the bike valve, adjust the pump, and fill the tire with air. Once you have the right air pressure, you’ll be ready to ride again.

Prepare the bike

The first step on how to use a bike pump is to get your bike ready. Make sure your bike is standing and won’t fall over. Once you’ve done that, move on to the valve.

Both Schrader and Presta valves have a dust cap you’ll need to unscrew. Store the cap in your pocket or another safe place so you don’t lose it.

A Schrader valve is ready once the dust cap is off, but a Presta valve has one more step. You’ll need to unscrew the valve cap and expose the stem.

Adjust the pump

The next step is to get your pump ready. Be sure to read and follow any safety instructions that come with the pump so you can stay safe while you operate it. You can’t have fun riding your bike if you injure yourself while filling up the tires.

Press the nozzle to the tire valve. This is all you have to do for some pumps.

Others have a lever near the nozzle that locks the nozzle onto the valve. This requires you to move the lever both to lock it in place and remove the nozzle from the valve.

Fill the tire

Once you have everything ready, follow the instructions for your bike pump. It will tell you how to use a bike pump safely and effectively.

A floor pump requires you to stand on the bottom and use your arms to operate the pump. This kind of bike pump is popular in most households. It’s easy to use and doesn’t require much effort.

A hand pump is small and portable, so you can fill your bike tires with air on the go. Instead of using both arms to operate this pump, you only need one hand to steady the pump and the other to work it. However, it doesn’t fill tires nearly as fast as a floor pump.

Once you’ve filled the tires to the appropriate air pressure, you can remove the nozzle from the tire valve. Screw the valve and dust caps back on, and you’re ready to hit the road.

Check the air pressure

It’s difficult to know how to pump up bike tires if you don’t know what the air pressure needs to be. The best way to know your bike tire air pressure is to look at the tire itself. The side of the tire should give you a minimum and maximum pounds per square inch (PSI).

If your bike pump has an air pressure gauge attached to it, you can check the PSI as you pump. You can also purchase a separate tire pressure gauge that can check the pressure after you pump.

AstroAI Digital Tire Pressure Gauge 150 PSI 4 Settings Car…

  • Check out our VIDEO on the…
  • Designed to maintain correct…
  • Nozzle easily forms a seal…
  • Simply press “ON/UNIT/OFF”…
  • 1 Year Warranty and battery…

If you don’t have an air pressure gauge, it’s possible to check the pressure with your hands. This is less accurate, but it can help you get back on your bike in the meantime.

Do this by pressing your thumbs against the tire’s side. On a road bike, you should barely be able to press into the tire. On a mountain bike, your thumbs should only move the tire by about a centimeter.


In some cases, you may find that your bike tire won’t take air as you pump. There are a few steps you can take to make sure everything is working correctly.

The first is to make sure the air pump’s nozzle is secure on the tire’s valve. It should go on straight, and there shouldn’t be any air seeping out. If the nozzle isn’t secure, you’ll likely pump some air before you realize the tire isn’t taking any of it in.

If the nozzle is secure, you may find that the pump won’t even go down to pump air. The best way to remedy this problem is to remove the nozzle from the valve. Then press down on the stem a couple of times. The valve stem may have gotten stuck, which would prevent air from going into the tire.

After this, you should be able to reattach the nozzle and fill the tire with air.


If you know how to use a bike pump properly, you can get back on the road in no time. Be sure to check your bike’s tire pressure regularly so that you can keep them at the recommended PSI. Failure to do this can not only damage your bike, but it can also affect your riding experience.

The best bicycle pump for you will have a nozzle that matches the valves. Once you have the right pump, you’re ready to fill your tires and get back to riding.

Do you have additional tips and tricks on how to use a bike pump? Let us know in the comments section.

Featured image by: Freepik

Here’s How to Move a Gun Safe in Simple Step-by-Step Instructions

You find yourself faced with a move, and now you need to know how to move a gun safe. It’s a moment you dread because the gun safe is heavy. However, you need to know how to transfer a gun safe efficiently and safely.

It can feel a little daunting when you have to move your gun safe from one place to another. By nature, a gun safe is a dangerous thing. Not only is it bulky and awkward, but it is also incredibly heavy, and even though you dread moving it, you know you have no choice.


When you consider the question, how to move a gun safe, there is only one answer. Safely.

You must take great care to remove the contents of the gun safe and hire the right equipment with which to move the safe itself. A good pair of gloves will prove essential, as well as a sturdy dolly cart for you to maneuver the safe. Additionally, you will need to ensure your path of movement remains clear and that you hire a suitable truck in which to transport your gun safe.

FCH Gun Safe Electronic 5-Gun Rifle Safe Large Firearm Safe…

  • Please make sure to purchase…

We would typically recommend that you hire a professional team of movers to perform this difficult task. However, you may wish to carry out the procedure yourself. Consequently, you need some hints and tips on how to move a gun safe.



A gun safe is heavy enough as it is, so ensure you empty out the contents before you begin. Make sure you store any ammo in a separate, secure box.

Clear the area

If you are moving to a new property, then you will need to remove the safe from your existing property. As such, ensure your path remains clear of obstacles. Also, park your truck as close as possible with the ramp ready to receive your safe.

Ask for help

Gun safes are very heavy. So, you should seek the help of friends or family to move the safe. There is little point in moving the safe by yourself if you hurt your back! So ask for help to make your life easier and safer.

Protect the surrounding area

Protect any walls and furniture you may pass with scratch-resistant material. If the safe bangs into furniture, it will scratch it. If you can move everything out of your path beforehand, all the better.

Make more space than you need

Due to the cumbersome nature of the safe, a bit of wobbling and curving from side to side may occur as you move it. Therefore, create more space than you think you need!

Be prepared

Use planks of wood as ramps wherever you may encounter steps. However, if this proves impractical, you will need additional hands to help you maneuver the safe up or down such obstacles. Get the pizzas in and plenty of cans!


Gun safes are heavy! Furthermore, the extra weight in the truck will result in extra gas consumption. You will need to budget for the additional fuel.

Safety first

When you wonder how to move a gun safe, the answer remains the same. Safely. Invest in hiring a good quality furniture dolly, or even a forklift truck if practical. You need to make the process as easy for yourself as you can. If you struggle, you may only injure yourself and those around you.



When it comes to the actual move, take your time, and wear your protective gloves.

G & F 15196L Seamless Nylon Knit Nitrile Coated Work Gloves,…

  • Ergonomically designed for…
  • Seamless fit provides maximum…
  • Breathable Nitrile coating
  • 100% Nylon Gloves shell…
  • SOLD by 6 Pair Pack

Gather the masses

Instruct your helpers to stand on one side of the safe and lean it back gently. Now you may slide the dolly underneath the safe.

Secure the safe

The last thing you want is the safe tipping or sliding off the dolly as you move it. Therefore, ensure the safe sits on the dolly properly and remains balanced.

A gun safe is so massive that if it tips, there remains very little you can do about it. It may cause serious injury. Ensure the dolly is fit for the purpose and large enough to take the safe comfortably.

Proceed to move the safe

With your path clear, you may start to move the safe. Take your time. Stop regularly to ensure the safe remains adequately balanced on the dolly. Move obstacles out of the way rather than trying to move the safe around the obstacle.


Corners and sharp bends can prove tough. Try to remain calm and perform each maneuver slowly. Try to support the safe on the side opposing the direction you are turning into. Consequently, the more help you have here, the better.

Swing the dolly out a bit further than you think you need to allow the safe and dolly to turn at a more comfortable angle.


So you have made it to the truck. Now you have to get the safe onto the truck.

Watch the video below:

Helpers assemble

Gather as many helpers as you can and position yourselves behind the safe. Tie straps around the safe so that one person may pull the safe while the others push. Keep up a gentle momentum with the person pulling acting as a guide for the direction of the safe.

Once the safe slides up the ramp of the truck, you can position it into its final position. If possible, ensure the safe is trapped down.


It is no mean feat to move a gun safe. Hiring a team of professionals will take the stress out of the move. However, with a little help and a lot of muscle, you can move the gun safe yourself.

Have you ever moved a gun safe? Perhaps you have some advice you would like to share with us. Why not leave us a comment in the space below as we would love to hear from you.

Featured image by: Amazon

Yeti Tundra 45 Review: A Rugged Camping Cooler

Are you planning on to take a camping trip but do not know what the best cooler is to buy? Well, you have come to the right place. We have an amazing Yeti Tundra 45 review for you!

Finding the right cooler is very important. So, is the Yeti Tundra 45 that cooler?



image by pexels

The Yeti company was founded in 2006 by brothers who love the outdoors but were tired of cheap, useless coolers. Once they created a cooler, they went on to make other stuff.

Now the company has bags, drinkware, gear, and accessories. Yeti has become a very well known company and loved by many. Users can not stop raving about all the benefits they get from these products.



image by pexels

Yeti offers some pretty amazing products with a few extra benefits to make the purchase even easier to complete.


A pretty awesome thing about Yeti is they let you pick from so unique designs for the products you buy.

So, let’s just say you have a favorite football team; they have got you covered. The company will add the logo and design on your cooler!.


Some users have a Yeti cooler, and after four days, they wonder if the ice would ever melt. That is right, the ice has been proven to last up to four days inside a Yeti cooler.

Now, it could melt or last longer depending on the temperature outside of the cooler, but for the most part, you are good to go up to four days.


Having options when buying a product is a huge plus. Yeti coolers come in many sizes and colors. No need to worry about carrying around the heavy cooler, you can add some wheels.

Now, we know you have come here for a Yeti Tundra 45 review, but we wanted you to know there was more behind Yeti than the basics. Without further ado, here is a Yeti Tundra 45 review for you.


YETI Tundra 45 Cooler

  • One piece roto-molded UV…
  • Constructed of food-grade…
  • Two inches of polyurethane…
  • T-latch keepers are molded…
  • Recessed drain plug and rubber…

The Yeti Tundra 45 can hold up to 26 cans with a little bit of ice or 35 pounds of ice at one time. The Tundra 45 holds 37 quarts.

This cooler has a proven technology to keep the animals away with the rubber pulldowns to close the top. The inside of the Tundra 45 has a rubber tight seal to prevent any heat from entering the inside of the cooler and a plug on the lower side to let the water out.

Each Tundra 45 cooler has 2 inches of insulation on the side to keep your stuff super cold.  This cooler has a rope handle on the side for you to pull the cooler, or you can pick it up with the built-in handles. Yeti also provides each customer with a dry food basket to be placed inside the cooler.

Users love how long their ice lasts and how durable this cooler is. A few users do not like that it is called 45 even though it only holds 37 quarts.

Please check out this awesome informational video below:


  • Holds 26 cans with ice at one time

  • Rubber tight seal

  • Dry food basket included


  • Expensive

  • No wheels

Where to buy



image by pexels

We know when you are out camping, hunting, fishing, or even just a picnic, you want your things to stay nice and cold. So we took to professional reviews, to see what makes a cooler the very best.

After we read through what they had to say, we then read many user’s comments about the products.

Once we were done, we were able to give you an amazing Yeti Tundra 45 review and provide you with some great competition to help you compare.


When you are buying a cooler, you want the very best, right? Well, we totally understand, and we have got you covered with a little competition against the Yeti Tundra 45 review.

Please take a moment and see what other options are out there in the list below.


OtterBox Venture Cooler 65 Quart – Shoreline (Citadel…

  • The OtterBox Venture 65 Cooler…
  • Mounting system: attach…
  • Tough latches: lock in…
  • Slanted interior bottom:…
  • External dimensions: 40.01″ L…

This OtterBox Venture cooler can hold up to 65 quarts, and it is made in the United States. This cooler has tough latches to keep the top closed and a rubber seal to keep the heat out.

The Venture cooler can hold 36 cans and a little bit of ice or 75 pounds of ice at one time. OtterBox product makes this product with a slight angle to make draining much easier.

This cooler has built-in handles on the sides to make carrying it a little easier. Each cooler comes with a bottle opener built-in, and a dry storage tray. You can also purchase more add-ons if you want.

Users are very happy with how much this cooler can hold. A few users say the ice does not last long enough.

Check out this amazing overview below:


  • Holds up to 65 quarts

  • Tough latches to keep animals out

  • Angle design for better draining


  • Expensive

  • Does not come with wheels

Where to buy


Frosted Frog Gray 45 Quart Ice Chest Heavy Duty High…

  • ADVANTAGES: Military grade…
  • EXTREMELY TOUGH: Virtually…

Frosted Frog makes a cooler that holds up to 45 quarts, and it has three inches of insulation. This cooler has rubber pull down latches to keep it sealed shut when not in use and a rubber seal to keep the heat out.

The Frosted Frog gray cooler has ropes with handle covers for you to be able to carry this cooler everywhere. The cooler also has an easy to pull drain plug to get the water out. The company provides each customer with a five-year manufacturer warranty.

Users say this cooler does the trick, and they recommend it to everyone. A few other users say the ice does not stay over two days.


  • Five-year manufacturer warranty

  • 3 inches of insulation-to keep everything cold longer

  • Easy pull plug


  • Expensive

  • No wheels

Where to buy


Cascade Mountain Tech Heavy- Duty Cooler Built-in Bottle…

  • Tough roto-molded…
  • Ice retention for days: with 3…
  • Perfect for every occasion:…
  • Dimensions: 45-quart internal…
  • Want accessories? Purchase at…

Cascade Moutain Tech makes a heavy-duty cooler that holds up to 45 quarts. This cooler has durable pull-down rubber latches to keep the wildlife out. The Cascade Moutain Tech cooler can hold up 36 cans and ice at the same time.

Each cooler comes with a built-in bottle opener and rope handle to carry it everywhere you go. There is also a pull plug to drain the water that is attached to the cooler.

Many users say the ice can last for more than two days. A few users say the cooler gets very heavy when it is full, so you need two people to get the job done.

Check out the details on this cooler below:


  • Holds up 36 cans with ice at one time

  • A built-in bottle can opener


  • Expensive

  • No wheels are included

Where to buy


Fatboy 45QT Hard Sided Rotomolded Chest Ice Box Cooler White

  • Extreme Hard Sided Roto-Molded…
  • External Dim: 26.5″W x 16″D x…
  • Internal Dim: 20.5″W x 11″D x…
  • 5 Year Limited Warranty
  • Holds Ice: Up to 8 Days Color:…

This Fatboy cooler can hold up to 45 quarts, or it can hold up to 60 cans, and it has rubber pull down latches. The cooler comes in five different colors and a rubber seal to keep the heat out. This cooler has a handle on each side for you to carry the cooler everywhere you go and an easy-to-pull plug to get the liquids out.

There is a button on the outside of the cooler you can push to help empty the water faster. Each Fatboy cooler has a bottle opener attached on the side and an option to lock the cooler with your lock. The company claims this cooler will keep your ice for up to eight days without melting.

Users love this cooler and say it does keep the ice for long periods of time. Other users think it should come with a dry food basket or wheels.

Please take a moment and watch this video:


  • Pull down rubber latches

  • Bottle opener

  • Able to lock the cooler


  • Expensive

  • No wheels

Where to buy


Igloo BMX 52 Quart Cooler with Cool Riser Technology, Fish…

  • ABOUT IGLOO: Born from a…

The Igloo BMX holds up to 52 quarts or 83 cans with a little bit of ice. It is held shut with rubberized latches, and it has handles on each side for you to carry. The company claims this cooler will keep ice perfect for up to five days.

There is an extra feature on this cooler where you can strap the lid and cooler down with the four tie-downs openings. Igloo claims the cooler is rust-resistant, and it has measurement marks on the lid. The easy to open water relieve valve can also be attached to a hose.

Many users say the ice lasts more than four days. Other users love how much space they get in this cooler. A few users say the cooler leaks too much.

Check out this quick video below that shows in-depth the cooler’s features:


  • Holds ice for five days

  • Can hold up to 83 cans

  • The valve can be attached to a hose

  • Able to measure your catch on the lid


  • Expensive

  • Wheels are not included

Where to buy



So, after reading our Yeti Tundra 45 review and its competition, you are probably wondering is the Yeti Tundra 45 right for you? Well, we can definitely say the Yeti Tundra 45 is amazing at taking a long time for the ice to melt, and the cooler can keep the animals out. The Yeti Tundra 45 is perfect on day trips and overnighters, but it only holds up to 37 quarts.

Overall, it is an amazing cooler but with a little above average price tag. So, if you are okay with the price, it is definitely worth the buy. If you do not want to spend that much, we have provided you some other awesome options.

Now off you go to the next adventure!

Have you ever owned a Yeti Tundra 45 cooler? If so, what did you like about it most, and why? Please let us know in the comment section below.

Featured image by: Amazon

Here’s How to Patch a Bike Tire and Get Back on the Trail ASAP

When you ride out on the trail, you may need to know how to patch a bike tire. There is nothing worse than finding yourself stuck out in the wilderness with a flat. What’s more, learning how to repair a tire can prove tricky.

Imagine you are 15 miles out from your destination. Suddenly, you are riding over sharp, uneven ground, and your bike feels sluggish and unresponsive. To your utter dismay, you discover that your bike has a flat tire.



image by pixabay

Punctures in your bike tires may not happen regularly; therefore, you must learn how to patch a bike tire should the eventuality arise. The last thing you want is a long hike back home because you find yourself stranded out on the trail with a flat.

With some essential tools and a little know-how, you can quickly and effectively repair your tire out in the field. It is always worth carrying tire levers, a spare tube, a tire plug kit, and a good quality bicycle pump.

WOTOW 16 in 1 Multi-Function Bike Bicycle Cycling Mechanic…

  • It can help you fix most…
  • With good quality, durable,…
  • Allen Keys: 2, 2.5, 3, 4, 5, 6
  • 16 function all in one…
  • 3 pcs Nylon pry tire rods,…

Once you have located the puncture, you can quickly insert a tire plug without changing any of the hardware. Moreover, once you pump your tire back up to pressure, you can return to your trail within a very short time.

However, there exist a few different types of puncture that you need to understand to learn how to patch a bike tire.



image by pixabay

There are three different types of flats you may experience out on the trail. A good indicator of the kind of flat you have is how it sounds. Does your flat make a hissing noise? Did you hear a loud bang? Perhaps your tire did both? To understand how to patch a tire, you must first understand the problem.


This type of flat includes pinch flats. Punctures usually make a hissing noise because you have gone over a nail or glass. The foreign object pierces the tube, and consequently, the air leaks out, and you end up with a flat.

The dreaded blowout

If your tire goes bang, then you have a blowout. A sudden tear in the tire causes a blowout. Blowouts tend to be catastrophic and require a change of tube. However, a large patch called a boot, may prove sufficient enough to get you home. A boot is nothing more than a makeshift patch folded several times and glued over the tear to allow you to pump the tire up.

While this type of repair is temporary, something as simple as a snack bar wrapper, folded over four to six times, and glued over the tear will form enough of a repair to get you home.

Deterioration flats

Deterioration flats can make a hissing noise or a bang. As the name suggests, time and age gradually wear out the rubber, causing it to either lose air over time or fail altogether. When you learn how to patch a bike tire, it is always worth getting into the habit of checking over your tires regularly. Check for cracks or bulges, which may indicate a looming deterioration flat.



image by pixabay

Most bikes have two types of tires, and it is crucial you know which type you have before you prepare your patch. Tubeless setups don’t have an inner tube. However, as typical as this type of tire is, you may find your bike does have an inner tube.

Using a plug for tubeless tires

A plug kit forms a fast and reliable repair for your deflated tire. The kits come complete with a small strip of rubber and an insertion device, which allows you to repair the hole without having to change any hardware. However, you will need to remove the tire first to locate the offending puncture.

LEZYNE Tubeless Bicycle Tire Repair Kit Mountain & Road…

  • Repair kit with extensions
  • Aluminium finish
  • Comes with 5 strands

Once you find the hole and insert your plug, you can re-inflate your tire using your bicycle pump. Pump the tire up to the correct pressure. However, continue to check the puncture area as you pump up the tire to ensure no air escapes.

Once complete, you can start riding again. Initially, check the repair every so often to make sure it holds fast.

Patching a tube tire

If your tire has a tube, then you will need to remove the wheel. Keep your bike upright as you remove it. Additionally, if the puncture is in a rear wheel, then shift your drive-chain into the hardest gear. If your bike has rim brakes, then you will need to loosen the brake.

Take up a position

Position yourself on the non-drive side, opposite the chain and either open the quick release or unthread the thru-axle to remove the wheel.

Unseat the tire

Use a tire lever to remove the tire by hooking the rounded end under the bead. Fix the other end to a spoke before hooking the second lever under the bead next to the first tire lever.

However, you may not need to remove the entire tire to patch the puncture.

Locate the puncture

With the tire off, you can pull out the old tube to find the hole. Use your fingers to carefully feel your way around the tube until you find the offending sharp object or puncture.

If you cannot find the puncture, then you can pump a little air into the tube. Because the air will hiss out of the puncture, it should make your life easier when locating the hole.

Apply the patch

Once you have located the problem, use a patch repair kit
 to seal the hole. Wait until the glue goes tacky before applying the patch. Re-inflate your tube enough to allow it to hold its shape before placing it back inside the tire.

RocRide 16-PC Inner Tube Patch Bicycle Repair Kit. Also for…

  • LIGHT WEIGHT only 2.3 oz and…
  • COMPACT only 4.75″ x .2.5″ x…
  • SIMPLE TO USE Scuff punctured…

Finish by re-installing the tire onto your bike before pumping the tire back up to its optimum pressure.


When you need to know how to patch a bike, you need to know what type of tires you have. Most bike tires these days don’t employ an inner tube. Therefore, it is always worth carrying a tire plug kit on your travels. However, tire levers, a bicycle pump, and a patch repair kit should still form your most basic tool kit.

BV Bicycle Ergonomic Bike Floor Pump with Gauge & Smart…

  • Steel barrel
  • Floor pump with easy to read…
  • For Presta and Schrader Valves
  • Egromically designed…

Do you have any hints and tips for patching a bike tire? Why not share your experiences by commenting in the space below as we would love to hear from you.

Featured image by: Pexels

How Long Does a Tire Plug Last?

You have repaired your punctured tire using a plug, and you can’t help but ask yourself, how long does a tire plug last?

As a conscientious bike driver, you want to ensure your repair is safe and will stand the test of time. After all, the last thing you want is the worry about a sudden blowout caused by a shoddy repair.



image by pixabay

You successfully used your tire plug kit and used a good quality bicycle pump to re-inflate your tire. However, as you push off to continue your ride, a single nagging question haunts you. How long does a tire plug last?

The simple answer is indefinite. A well-performed tire plug repair will retain air within your tire and prevent deflation. Because of the way a tire plug works, it is designed to form a permanent fix for your bike. That is, however, until you have another puncture!

However, before you ask yourself, how long does a tire plug last, it is worth understanding how they work.


bike wheel

image by pixabay

Tire plug repair kits are readily available from many bicycle suppliers and offer a simple yet effective way to repair your tubeless bike tires.

How the plug works

Tire plugs consist of strips of leather, covered with a sticky, un-vulcanized rubber compound.

Vulcanized rubber has an intermolecular system with highly cross-linked polymer chains. In other words, the rubber retracts to its original shape when exposed to heat or pressure. Unvulcanized rubber does not act in this fashion.

How the magic happens

When you use your plug-repair kit on your bicycle tires, you force the sticky unvulcanized rubber into the hole. Consequently, the plug fills the hole.

When you set off on your journey, the heat and pressure of the wheel react with the sticky substance, and it vulcanizes. As a result, the repair becomes a part of the bicycle tire to form a permanent fix.

Different Rules for Cars

Please note that legislation regarding the use of tire plugs states that a plug must be used in conjunction with a patch when it comes to cars and motorized vehicles. Also, a qualified professional must undertake the repair.


tire flat

image by pixabay

When you ask the question, how long does a tire plug last, you must also take into account some crucial points.

The good bits

A tire plug constitutes a quick and low-cost solution to repairing small holes in your bicycle tires. Additionally, the repair will last for the lifetime of the bike tire. By carrying a kit with you when you venture out, you may quickly and efficiently repair your tire flat on the go.

The downside

Tire plug repair can fail. However, this is usually due to the inappropriate application of the plug. If you try to use the plug repair on a large hole, then consequently, the repair may fail.

It is essential to use the plug method for smaller holes, such as those caused by nails. Large tears or rips will not prove so effective to fix with a plug kit.


woman biking


Sometimes, you may have no choice but to replace the tire. In the case of a catastrophic blowout, no amount of patches or plugs will solve the problem. Safety should always sit at the front of your thoughts, and it is far better to replace your tire if in doubt. Also, consider consulting a professional if you feel concerned about your repairs.


The plug kit forms the perfect companion for your tubeless bicycle tires. If you ask yourself, how long does a tire plug last, you may also wonder how to use one.

Genuine Innovations G20439 Tubeless Tackle Tire Repair Kit…

  • Durable and reliable. It just…
  • Includes a Side of Bacon (5…
  • Alloy weatherproof storage…
  • Features a strong plugged tool…
  • Fast to repair and easy to use

Push in the plug

It may prove a little challenging to locate the puncture. However, if you pump the tire up a little, you should hear a hissing sound. Alternatively, run your fingers around the tire to locate the offending problem. A combination of both techniques should enable you to discover the puncture before you begin.

Also, if you have a water bottle with you, try spraying a little water over the suspected damage. If tiny air bubbles appear, then you have found the culprit!

Sports Water Bottle, 400/500/700ml/1L, BPA Free Leak Proof…

  • Transparent & Lightweight…

Start by threading the plug through the applicator with equal amounts sticking out from both ends. You may have different sized plugs in your repair kit, so use a plug appropriate to the size of the puncture.

Push the applicator through the puncture hole in your bike tire. This will require a little brute force. The needles of the plug repair kits tend to look quite robust, so you will need to flex those arm muscles. You need to push it in far enough so that at least half the plug remains inside the tire while the other half sticks out from the tire.

If you have difficulty pushing the applicator in, add a little more air to the tire as the extra pressure will help you to push the applicator through the rubber. However, take care not to push the needle in too far. You don’t want to lose the repair strip inside the tire.

Pull out the applicator

Once you have achieved the above step, you may proceed to pull the applicator out of the tire. Trim the ends of the plug before you re-inflate your tire.

Look out for the tire bead

Make sure the tire bead is in place. Sometimes, a puncture will result in the tire bead becoming unseated. If so, you will need to attend to this with your toolset as best you can as you inflate your tire.

Multi Tool 19 Gold

  • Includes 19 Tools
  • Comes with a Tool Flask
  • Includes Two Phillips and Two…
  • Has a Universal Chain Tool
  • Four Spoke Wrench Sizes

Use a bicycle pump

Use a good quality, accurate bicycle pump to re-inflate the tire to the recommended pressure.


We now know that a tire plug in a bicycle tire repair can last indefinitely. We also understand that for motorized vehicles, a professional must use a tire plug and a patch to form the necessary repair and meet the requirements of the law.

Have you used a tire plug on your bike? Perhaps you have some advice to offer? Why not leave a comment below as we would love to hear about your experiences.

Featured image by: Unsplash

How To Clean A Rifle In 7 Simple Steps

Since rifles came into existence, it has always been encouraged for someone to learn how to clean a rifle properly. A rifle can be many things and has often been regarded as something that shouldn’t exist by those that fear it. However, a rifle is a versatile tool that provides food, provides a defense to the owner and their family, and a sporting item.

Due to the fact that rifles and all firearms are messy weapons and tools, cleaning a rifle is an important ritual. Furthermore, learning how to clean a rifle can be a sign of learning, understanding, and even mastery over the rifle. However, these tools have become a part of life, and it is only fair to learn to maintain them properly. Let’s put it on safe and head down-range to take a closer look.

graphic illustration of a rifle

How to Clean a Rifle: A Brief Overview

All firearms are subject to dirt, debris, and fouling from the environment, as well as the cartridges they fire. This fouling damages your rifles’ barrel, rifling, and chamber, causing a variety of dangerous reactions that are costly and tragically irreparable. Furthermore, continuing to use an unclean rifle can lead to injury and even fatalities, due to the rifle exploding.

Maintaining a rifle frequently and after each use ensures accuracy, safety, and a longer lifespan, for you and your rifle. Additionally, well-maintained rifles are less likely to jam or have a failure occur, ensuring a fail-free fire every time. Cleaning and maintaining a rifle should are the most important things to do when owning a good rifle.

graphic illustration of a rifle

How to Clean a Rifle: Into the Breach

Before you begin cleaning your rifle, a few rules should be considered and followed to ensure safety and space to work. Checking and then double-checking that the rifle is unloaded, magazines are out or empty, and there are no rounds chambered. Empty the magazine by hand and take all the ammunition and store it away from the rifle for added safety.

Whether you are shooting rimfire or a long-range rifle, being safe and mindful of your rifle is excellent. Practicing proper rifle safety is just as good, if not more so than practicing how to clean a rifle. However, we are going to go through a simple guide of exactly how to clean a rifle now.


disassembled rifle

Image: CC BY 2.0, by Bill Bradford, via Flickr

Setting the table up to work on your rifle would be the first task, as to avoid damaging the rifle. The first step is to disassemble your rifle, or field strip, which means removing the bolt, or bolt carrier. You will also want to remove any sight systems, accessories, and gadgets from your rifle to prevent interference during cleaning.

Once you have removed the operating mechanism of your rifle, you can then inspect the mechanism itself for fouling and damage. Depending on the rifle you own, strip the rifle down so you can clean the barrel and chamber safely. Be sure to inspect all the internal parts for dirt and fouling and set them aside to be cleaned.

Cleaning the bolt channel and chamber mouth

At this point, you will begin to remove any course grit and debris inside the magazine well and surrounding areas. All rifles will have grooves and spaces which catch a lot of the dirt and go unnoticed. Therefore, it is a good idea to flush out and clean those particular areas and spaces thoroughly.

With the external areas clean, you will move onto the chamber mouth, carefully and gently wiping the surface down. Also, if you have an internal magazine, it would be a good idea to clean it out thoroughly as well.

Cleaning the barrel with a nylon brush

With the previous step complete, you should move onto cleaning the barrel itself with a cleaning rod and nylon brush. Gently push the rod down the length of the barrel, keeping your hand off the rod itself and on the handle. Afterward, once at the muzzle, unscrew the brush and retract the rod and then re-attach the brush and repeat it.

You should repeat this process several times until you are sure you have gotten the most out of the barrel. Although, it is essential to remember to not pull the brush back down the barrel, pulling dirt back. Be sure to inspect the brush to see the accumulated dirt and dust or wipe it off before returning.

Initial cleaning with a patch

Attaching a jag to the cleaning rod and threading a patch into the jag is the beginning of the next step. Gently push the rod down the barrel several times, repeating the same process as with the nylon brush before. Be sure to inspect the patch for dirt to mark your progress and continue the process until you don’t see any dirt.

Deep-cleaning with barrel solvent and oil

This next step will see you using your brush and patch in conjunction with barrel solvent and oil for cleaning. Add the barrel solvent to the brush and push it down the barrel to break up any built-up fouling. You will want to repeat this process, and to be sure, look down the barrel from the rear.

With the barrel clear and clean, you will want to oil it in the same process as the ones before. Applying oil to a patch or two and running the rod and jag down the barrel a few times. Finally, incline your rifle with the muzzle downwards to allow any run-off to exit out of the barrel and muzzle.

As part of general maintenance

If the rifle has not been fired, you should clean the old oil out of the barrel with a clean patch. And, then run an oiled patch through to lightly oil the inside of the bore of the rifle. This will keep the rifle in good condition for when you do use it, but it is a good practice. Even when not in use for a time, it is also a good idea to oil the barrel and the exterior.

After firing smokeless full metal jacket ammunition

It is a good idea to clean the barrel with a brass brush and bore solvent, as per the solvent instructions. To ensure the rifle is kept clean, run a few patches through the barrel until they are clean. Additionally, it is good practice to oil after every cleaning, as it keeps the rifle in good condition for longer.

After firing smokeless lead bullet loads

For this situation, start by scrubbing the bore with bronze brushes and copper wool to remove the worst lead. Alternatively, use a solvent made for lead bullet fouling, or if using the same solvent as above as per the manufacturers’ specifications. Again, clean the barrel with patches until sure and apply oil to the barrel after the cleaning process.

After firing military surplus ammunition

After firing military surplus munitions, strip and submerge the metal parts of the rifle in warm water and ammonia. To explain, military surplus munitions are highly corrosive and foul the metal surfaces of the rifle. Soaking the parts in water and ammonia already does an excellent job of cleaning, but brushing the parts helps.

You will want to strip your rifle of all metal parts, soak and then brush them to remove all corrosive residue. Alternatively, you can soak patches in the water and ammonia and run them down the barrel to thoroughly clean it. An air compressor will dry the parts and the spaces quite thoroughly, also, remember to oil your rifle when finished.


With the cleaning of the internals complete, you can touch upon the mechanism parts, clean and oil them. It is a good idea to wipe out the bolt race or receiver with a lightly oiled patch. And with all the little bits finished, you can reassemble your rifle while still checking each part for dirt.

Finishing off

Now, with your rifle fully reassembled, make sure to clean the outside surfaces of the bolt, receiver, and barrel. A lightly oiled patch will help to get all finger marks off the surfaces, due to acid in the skin. Wiping down the entire rifle of dirt with a slightly oily rag or cloth to keep it in good condition.

graphic illustration of a rifle

How to Clean a Rifle: The Essential Cleaning Kit

Every quality rifle deserves a quality cleaning and a quality cleaning kit to ensure that it remains a factor. Here we will take a look at what items are found in an essential cleaning kit.

cleaning tools

Image: CC BY 2.0, by Joe Goldberg, via Flickr

graphic illustration of a rifle

How to Clean a Rifle: Summary

rifles and cleaning tools

Image: CC BY 2.0, by Robert Tadlock, via Flickr

To this day, learning how to clean a rifle is still a rite of passage for those who respect what a rifle is. Through the ages, parents have taught their children the importance of firearms, specifically the importance of caring for them. Cleaning and maintaining a rifle significantly influences what it can do and how well it will do it.

Hence, ensuring it is clean ensures that when it’s used, for whatever purpose, it operates correctly every time. Rifle care methods differ from situation to situation, but the core principles remain the same.

However, it is a good idea to keep an open mind regarding your case, before getting out the cleaning kit.

Do you have any tips for those learning how to clean a rifle? Let us know in the comments section.

Featured Image: CC BY 2.0, by Ryo Chijiiwa, via Flickr

Rifle Icon: by Freepik from

Nikon ACULON Rangefinder Review: A Gadget You Need On Your Next Hunt

The number of people hitting the woods and hunting, or teaching their children how to hunt, is on the decline. Here at, we would like to turn that trend around. So, today, we’re helping you keep your aim on point with this Nikon ACULON rangefinder review.

Whether you are a seasoned hunter or you’re just getting into the game, many hunters find a rangefinder to be an essential tool. You see, we all understand the importance of a clean, accurate shot — a rangefinder used with a scope is a great way to make sure that happens.

A decent rangefinder will locate your target and let you know within seconds how far away it is. Let’s find out in this Nikon ACULON rangefinder review if this is the equipment for you. Today, we’re going to find out not only how the Nikon Aculon performs, but also how it stacks up against its main competitors.

What Is a Rangefinder?

​Now, before we get into the specifics, let’s quickly discuss what it is that a rangefinder does. Simply put, a rangefinder is the fastest way to determine how far away you are from your target so that you can adequately aim your shot.

To use a rangefinder, you aim it downrange and focus the crosshair in the reticle on your target. Then, when you push the button, an invisible light beam hits the mark. An internal clock then calculates how far away you are from your target based on how long the light beam takes to pingback.

The distance, usually within a yard, then reads out on a digital display screen. A decent rangefinder will give you a reading in less than a second and even continue to recalculate as you aim at different things.

When you’re hunting, you know that when that animal appears, you only have a few seconds to set up your shot. So, the ideal rangefinder will be compact, fast, and easy to use and read. Also, most hunters prefer that their rangefinder comes with some magnification.

​The Nikon ACULON Rangefinder

Nikon 8397 ACULON AL11 Laser Rangefinder

  • At 3.6″x2.9″x1.5″ in size, the…
  • An uncluttered, easy-to-read…
  • Class 1 laser product, power…
  • Measurement Range 6-550…

​Now, to start this Nikon ACULON rangefinder review, we can tell you that this item is one of the smallest rangefinders on the market. At 3.6 inches by 2.9 inches by 1.5-inches, the Nikon 8397 ACULON A11 rangefinder is barely larger than a smartphone — and it only weighs 4.4 ounces.

Additionally, this Nikon rangefinder has a unique feature popular among hunters that might appeal to you. It includes a mode that automatically searches for the furthest thing away from you amongst a group of targets. This feature is especially helpful if you often have to deal with tall grass or a lot of trees.

On top of that, the ACULON includes multilayer coatings. These coatings ensure the highest possible light emittance downrange — eliminating many traditional interferences like reflection and fog.

Other features of the Nikon ACULON rangefinder:

  • ​Readout display: uncluttered gives distance in meters and yards

  • ​6 to 550 yards range

  • ​Class 1 laser product

  • 6x magnification

  • Waterproof

  • Push-button operated

  • 21mm objective lens

  • 1 yard increment readings

  • Comes with a carrying case

​What real customers have to say about the Nikon ACULON rangefinder

​Now, you can’t very well have a Nikon ACULON rangefinder review without checking in with the customers using the product. First of all, let’s talk about the good things everyone has to say about this equipment.

The good

​We found a ton of positive reports about this rangefinder. We found customers that stated this equipment is effortless to use, and its compact size makes it easily portable. In addition to that, a lot of customers are impressed with how easy it is to read the display screen, even while wearing glasses.

Many users report that this rangefinder is accurate too — some even say it’s range extends up to 600 feet. And we found several reviews from people who have used this equipment successfully for well over a year with no issues at all.

On top of that, the price point of this rangefinder is at the low end of the spectrum. Customers raved about value for the money with this product.

​The bad

On the downside, we found a couple of reports that people’s rangefinders were defective. Keep in mind, though that could be user error. Additionally, we found several customers that stated this rangefinder is a little too light.

You see, once you zoom in on something, the image can get shaky if you don’t hold the equipment perfectly still. And with its compact size, the ACULON can be tough to hold still. And there’s no way to use it with a tripod, as it doesn’t come with threads or a way to attach it to a surface.

​Pros and cons of the Nikon ACULON Rangefinder

Finally, to round out our Nikon ACULON rangefinder review, we’re going to do a final tally. Below, we list the pros and cons of the Nikon ACULON rangefinder.


  • ​Very affordable

  • ​Lightweight

  • ​Easy to use

  • Works as advertised

  • A ton of positive reviews from satisfied customers


  • ​The lightweight of the Nikon makes magnification shaky

  • ​Doesn’t range out as far as the Sig Sauer

​How We Conducted This Review

​So that you understand we did our homework for this Nikon ACULON rangefinder review, it’s time to discuss our process.

Now, to bring you the whole truth about the products we review, we hit every review site we can find. We read reviews both from the retailers that sell the product and professional summaries for a complete picture.

​How Does the Nikon ACULON Rangefinder Stack up Against the Competition?

​Well, you can’t very well get the whole picture in this Nikon ACULON rangefinder review without doing some comparison shopping. Below, we will compare the Nikon rangefinder to several products from Nikon’s main competitors and see how it stacks up against the competition.

Sig Sauer Kilo2200BDX Rangefinder

  • Sig Sauer sok22704 Kilo2200BDX
  • Laser range finding monocular
  • Rangefinders. Department -…

First up, we have a product from a company known for producing high-quality firearms — the Sig Sauer Kilo2200BDX rangefinder. We can tell you right off the bat that the Sig Sauer rangefinder is much more expensive than the ACULON. However, take a look at these specs:

  • ​Readout display: organic light-emitting diode (OLED) adaptive light that brightens or dims automatically as needed

  • ​Lens coating: Spectracoat (very efficient and works well in all conditions)

  • ​Range: 1.5 to 2,600 yards

  • Increment readings: 1 yard

  • Magnification: 7X

  • Objective lens: 25mm

  • Waterproof: yes

  • Fog proof: yes

  • Push-button operated

  • Connects via Bluetooth to an application on your phone

  • Weight: 4 ounces

  • On-board inclinometer: reads the incline/decline angle

​Although this is a Nikon ACULON rangefinder review, this Sig Sauer is one of the best rangefinders on the market. However, the price point puts it outside of a lot of people’s budgetary allowances.


  • ​Lightweight

  • ​Easy to use

  • ​Special night vision protection

  • ​The effective range is much longer than the Nikon

  • ​Has an onboard inclinometer

  • Top of the line rangefinder

  • The unique app allows you to track your progress with your phone


  • ​The high price point

  • ​Doesn’t always reach the advertised range

Bushnell 202208 Bone Collector Edition 4x Laser Rangefinder,…

  • Quality optics with stunning…
  • Beautifully designed with…
  • Displays exact distance to…
  • Bright, crystal clear optics…
  • Realtree Xtra camo pattern;…

​Next up for comparison on our Nikon ACULON rangefinder review comparison section is the Bushnell 202208 Bone Collector Edition. This rangefinder is a little pricier than the Nikon. Let’s take a look at the features of the Bushnell Bone Collector:

  • ​Readout display: in-view LCD

  • ​Class one laser

  • ​Range: 10 to 600 yards

  • ​Magnification: 4X

  • ​Waterproof: yes

  • ​Push-button operated

  • ​Objective lens: NA

  • ​Increment readings: 1 yard

  • ​Weight: 7.2 ounces

  • ​Comes with a carrying case

​As you can see, the Bushnell appears to be similar to the Nikon. Let’s find out what customers have to say about this product.


  • ​Lightweight (not as light at the Nikon)

  • ​Low price point

  • ​Works great for close-range shooting


  • ​Doesn’t work as well as the Nikon

  • Won’t range at the advertised distance

  • More expensive than the Nikon and it doesn’t work as well

TecTecTec ProWild Hunting Rangefinder – 6×24 Laser Range…

  • FULL PACKAGE; Complete…

​Next up on our Nikon ACULON rangefinder review, we’re going to compare the ACULON to the TecTecTec ProWild Hunting Rangefinder. The price point for this product is on par with the Nikon — let’s see if the features are similar as well:

  • ​Readout display: in-view LCD

  • Class one laser

  • Small, compact, and lightweight

  • Range: 1 to 540 yards

  • Magnification: 6X

  • Objective lens: 24mm

  • Increment readings: 1 yard

  • Waterproof: yes

  • Push-button operated

  • Weight: 6.5 ounces

  • Comes with a carrying case and lanyard

​As you can see, the TecTecTec has quite a few of the same features as the Nikon. Now, let’s find out what customers have to say about this product.


  • ​Low price point

  • ​Works as advertised

  • ​Lightweight

  • Easy to use

  • Great customer service


  • ​Sometimes the equipment breaks

  • ​Doesn’t range as far as the Sig Sauer

​​Nikon ACULON Rangefinder Review – Is This the Product for You?

Nikon ACULON Rangefinder

Image Via Flickr

Well, hunters and target shooters, there you have it — the full Nikon ACULON rangefinder review. As you can see, while the Nikon doesn’t range quite as far as the Sig Sauer, it’s much more affordable. For a full rundown of several other rangefinders, check out our list of the best rangefinders on the market.

If you’re hunting deer or other game from close quarters and you need a rangefinder that works at several hundred yards consistently, the Nikon and the TecTecTec are both excellent options. However, if you’re hunting game and you need a rangefinder that’s effective out past 300 yards or so, you’re going to want to look at something else.

Do you have a favorite rangefinder at home? Tell us about it in the comments.

​Featured Image Via Pixabay

Sig Sauer Kilo 2000 Review

Hunters have, at one point or another, read a Sig Sauer Kilo 2000 review. It’s one of those many tools that can help steer you in the right direction.

Inexperienced hunters often head home disappointed from their first hunting experience. That’s because they still need to be able to accurately gauge the distance from where they are to the target to make their shot count.

It’s a skill that may take years to master. In the meantime, all you can do is to fumble through your shots, eventually scaring the target away without hitting it even once. Embarrassing.

Thankfully, rangefinders were invented. These devices can help you get a more accurate aim, even if you’re a beginner.

Needless to say, rangefinders have become a must-have tool, especially for those who are just beginning to enjoy hunting. Is the Sig Sauer Kilo 2000 the best for you?

Sig Sauer Kilo 2000 Review: What It Is and How Do You Use It

Sig Sauer Kilo2200BDX Rangefinder

  • Sig Sauer sok22704 Kilo2200BDX
  • Laser range finding monocular
  • Rangefinders. Department -…

What’s a Sig Sauer Kilo 2000 review without delving into its features? But first, let us tell you: this rangefinder looks impressive.

It has a magnesium casing that makes it look elegant. You get to avoid the plasticky build of similar devices.

It also has rubber grips that help you hold on to the device even in the worst weather conditions.

Good quality glass

The Sig Sauer Kilo 2000 uses optics that are so good that professional shooters, the military, and law enforcement can use it for work. These optics have anti-reflective coatings, custom-calibrated adjustment turret systems, motion-activated light control systems, and ballistic reticles.

This rangefinder has all the technologies you would want to find in a device like this one. For instance, because of the LightWave DSP technology, you get extraordinarily speedy and accurate readings.

The Kilo 2000 has a max effective range of 1,600 yards. But depending on the target, it can be farther or nearer than that.

For example, reflective targets are ranged up to 3,400 yards. For everything else, they have to be nearer.

Trees can be ranged as far as 1,500 yards out, while you can only scope a deer not more than 1,200 yards away. It’s still impressive, nonetheless.

Ease of use

The Sig Sauer Kilo 2000 is very easy to use.

The user interface is straightforward. You only have two buttons: the RANGE and MODE buttons.

You can use the rangefinder by pressing the RANGE button once. This action will give you the reading you need.

However, if you need a continuous reading, you just long-press on the same button, and the device will update the measurements at a rate of four times every second. This feature is useful for targets that are farther away.

Lumatic display

The LCD comes with Lumatic technology that can adjust the brightness of your screen depending on the ambient light.

You can set it to AUTO so that the rangefinder will automatically adjust the intensity and brightness of the display.

You can also manually adjust the brightness by choosing from nine different presets.

Two modes of operation

You can use the Kilo 2000 to switch between the line of sight mode or the angle modified range.

Line of sight mode is used by long-range shooters as they can get information on both the distance and the angle of incline.

Meanwhile, the angle-modified mode or AMR is best for most hunting situations.

Other stuff you should know

Additionally, the Sig Sauer Kilo 2000 comes with a protective case, battery, lanyard, and instruction manual. It also has an OLED screen that you can see even under bright sunlight.

The CR2 battery can quickly provide more than 4,000 range calculations. However, it can run out quickly if you use HyperScan mode.

How We Chose the Alternatives for This Sig Sauer Kilo 2000 Review

We had four primary considerations in choosing the alternatives for this Sig Sauer Kilo 2000 review.

First is the magnification, which will determine how good the device is when it comes to spotting targets.

Combined with quality glass, magnification can help you find the targets quickly.

Next is the beam divergence, or how focused the beam is. Devices with tight beams are often more expensive and are excellent for targets that are farther away.

However, a larger beam divergence has fewer missed readings and allows you to hit the target without too much of a hassle.

You should also consider rangefinders with bigger apertures because these capture more return readings for a more accurate measurement.

We then researched different rangefinder models to make sure that they fit the bill and ticked our every box. We then checked their listings on retailer sites to make sure that they are available and well-received by users.

Precautions and Tips When Buying a Rangefinder

When you buy a rangefinder, be sure to check it thoroughly for defects the moment you receive it. It helps to ensure that the device works as it should. If it does not, you can return it while it is still under warranty.

Also, note that the manufacturer often claims a maximum range for their devices. However, in reality, the range-finding abilities of these devices will be affected by atmospheric conditions and the amount of available light.

Bright sunlight, dim environments, or snow can limit the effective range. Snow crystals can also diffuse laser beams.

As such, it is rare that a rangefinder ever gets to fulfill the maximum effective range promised by the manufacturer.

Lastly, you should be careful in handling rangefinders. Lasers can harm your eyes.

For this reason, you should keep the rangefinder out of your children’s reach. You should also remember that while most modern rangefinders are now water- and dust-proof, they’re still electronic gadgets.

Sig Sauer Kilo 2000: Before You Buy

As with any Sig Sauer Kilo 2000 review, you will want to see how this device compares to other rangefinders. How does the Kilo 2000 hold up to the TecTecTec ProWild Hunting Rangefinder, ATN Laser Ballistics 1000 Smart Laser Rangefinder, and the Vortex Optics Impact 850-Yard Laser Rangefinder?


TecTecTec ProWild Hunting Rangefinder

TecTecTec ProWild Hunting Rangefinder – 6×24 Laser Range…

  • FULL PACKAGE; Complete…

The TecTecTec ProWild Hunting Rangefinder promises that you will be able to scope targets from more than 500 yards away. The product boasts of an accurate reading within one yard at 300 yards.

It offers 6x magnification and a multi-layer clear lens. It is waterproof and lightweight at only 6.5 ounces.

If you need a handy rangefinder, then you will be glad to know that the TecTecTec ProWild Hunting Rangefinder measures only 4.1 by 2.8 by 1.6 inches. It also comes with a carrying case and a lanyard.

This device is very straightforward and does not have too many features. It’s perfect for beginners as an entry-level tool or if you just want to try out hunting with the use of a rangefinder.

However, it does not have angle compensation and does not measure slope. But it offers an excellent line of sight mode.

Unfortunately, it isn’t very accurate at close range. You may also wish that their customer service was a bit better.


  • Uses eye-safe class 1 laser

  • Dust- and water-resistant

  • Find distances without the added bulk and weight

  • Easy to use

  • Has a lanyard and carrying case included in the package


  • Magnification is average, and you may miss some targets

  • Doesn’t measure slope; no angle compensation

  • Accuracy is not guaranteed at close range

  • Customer support might not be helpful despite the one-year warranty

  • Some complaints about inaccurate readings


ATN Laser Ballistics 1000 Smart Laser Rangefinder

ATN Laser Ballistics 1500 Smart Laser Rangefinder…

  • Smart Ballistic Calculator -…
  • Long Range – it helps you…
  • Maximum Accuracy – complicated…
  • Pairs with Smart HD – it also…
  • Class 1 laser with <1mW…

The ATN Laser Ballistics 1000 Smart Laser Rangefinder is a far-reaching rangefinder that can cover up to 1,093 yards when conditions are favorable. This product is an accurate device and shows you your desired information in just a few seconds.

This device connects to your phone via Bluetooth so that your phone can do all the necessary computations. As a result, you get more computing power than similar devices without this feature.

Also, you will like how the app allows you to view the distance and other information you need on another screen. More importantly, this device gives you accurate data on distance and angles.
What’s more, the mobile app will also give you point-of-impact adjustments based on the data gathered by the rangefinder.

The manufacturer covers this product with a two-year warranty.

With top-quality glass and Bluetooth capability, this device is sure to stand out, especially for those who don’t like to put rangefinders near their eyes. However, you might find the build quality quite disappointing.


  • Smart and can connect to your mobile app via Bluetooth

  • The mobile app gives you a lot of additional features and more computing power

  • Excellent optics

  • Accurate

  • Waterproof and lightweight


  • Doesn’t pair with 4K scopes unless you update the firmware

  • Cheap build quality and feels like a toy


Vortex Optics Impact 850-Yard Laser Rangefinder

Vortex Optics Impact 850 Yard Laser Rangefinder

  • The Impact Rangefinder…
  • The primary HCD mode displays…
  • A scan feature gives…
  • The Impact runs on a common…
  • Fully multi-coated optics…

The Vortex Optics Impact 850-Yard Laser Rangefinder promises accurate ranges up to 850 yards out and offers a 6x magnification to give you a closer look at your targets.

The product has multi-coated optics that give you better light transmission even in dim settings. It also has a horizontal component distance and line of sight readings, both of which are angle-compensated.

It has a black LCD where you can see the information you need. This device works fast.

One of the things that set this rangefinder apart from most other similar devices is the compact dimensions that allow you to hold it comfortably in your hand. It measures 3.8 by 3.0 inches and weighs only 5.5 ounces.

You may find that the LCD is difficult to read when you’re outdoors. Plus, the manufacturer might have exaggerated its maximum effective range.


  • Wide field of view

  • Can range targets up to 850 yards

  • Can run on one long-lasting CR2

  • Lightweight and small size


  • 6x magnification is average for these devices, you may miss on some targets

  • Some complaints about not being able to range at 400 yards

  • Hard to read LCD, especially in low light conditions

Sig Sauer Kilo 2000 Review: The Pros and Cons

It’s not often that you come across a device that impresses at first glance and then blows your mind when you get to use it. The Sig Sauer Kilo 2000 is one of these products.

On appearances alone, the Sig Sauer Kilo 2000 already has the edge over its plasticky-looking competitors.

It’s very easy to use and has several technologies that make it very accurate and fast. It also features a very readable OLED screen that has auto-brightness control.

Not only does this feature makes it easier for you to read off the display, but it also protects your eyes when you view it in dim conditions.

It’s not the cheapest rangefinder out there, but for the features that you get, it’s a bargain.


  • Fogproof and waterproof

  • Premium looks

  • Impressive range

  • Can range reflective targets of up to 3,400 yards

  • Five-year limited warranty

  • OLED display

  • Accurate within in 0.5 yards at 500 yards

  • 7x magnification


  • Eye relief at 0.6 inches could mean that those wearing glasses may not be comfortable using this rangefinder

  • Uses class 3 laser, which may be harmful to the eyes

Sig Sauer Kilo 2000 Review: You Won’t Regret Buying It

Rangefinders typically work the same way. It shoots lasers to your target and then sends it back. The device will then calculate the time it took for the laser to reach your target and return.

All of that happens in seconds, and you get a reading either in yards or in meters. What makes each rangefinder different from another is the glass used, the smarts, and even the appearance.

This Sig Sauer Kilo 2000 review can confirm that this device excels in all aspects. The design is not only eyecatching but also functional.

It is apparent that a lot of thought has been put into its design, from the lightweight magnesium cover to the rubber grips. But what makes the Kilo 2000 stand out is how it works.

It is accurate and fast. It can measure both line of sight and slopes. And compared to other devices, it offers more features.

All of these reasons combined make the Sig Sauer Kilo 2000 very easy to recommend.

Have you decided on a device mentioned in this Sig Sauer Kilo 2000 review? Tell us which one in the comments.

Featured Image Source:

Best Rangefinder in use by Hunter on Expedition

Recommended For You

Top 15 Best Laser Rangefinders for Bow and Rifle Hunting in 2019: Ratings & Reviews

The Out sider

Get the latest product reviews and advice for hunting, survival, camping and the great outdoors.

See Also

Related Reads

Recent Posts